V33 Stain for Doors, Frames & Cladding Xtreme Protect
V33 Stain for Doors, Frames & Cladding Xtreme Protect is available to buy in increments of 1
Need a stain that will stand the test of time for your exterior woodwork? The
Xtreme Protect formula guarantees long-lasting performance and peace of mind.
For all exterior and interior vertical woodwork: doors, frames, cladding, shutters, gates, beams, pergolas, carports, railings...
On all types of European or exotic wood, new or old: oak, softwood, larch, Douglas fir, red cedar...
PROPERTIES
IDEAL PROTECTION
High resistance to UV rays and
(sun, rain, snow, frost, wind,
rain, snow, frost, wind...).
Water-repellent: enhanced
waterproofness.
ENDURING BEAUTY
A velvety satin finish, closer to the natural look of wood.
EASY APPLICATION
Compatible with all old woodstains,
including glycerol.
Non-drip texture for easy, drip-free
application.
Fast drying.
WHAT WE ALSO LIKE ABOUT THIS STAIN
Formulated with plant-derived resin, oil and wood fibers, not derived from petrochemicals or organic farming. The formula contains 25% biobased carbon on total carbon according to NF EN 16640.
Between coats: 3h Thorough drying: 12h
YIELD 12m2/l
0.75L - 2.5L
Light satin
Cleaning with water
Exterior
How to use
TOOLS
As desired or depending on project configuration :
Brush
Roller
Spray gun
PREPARATION
Wood must be bare, clean, dry and not greasy. Always round corners and sharp edges to ensure even coverage.
Rough wood: sand with 150-grit sandpaper to obtain a smooth surface and remove dust. Protect wood against insect attack or fungal growth with V33 Universal Treatment or Garden Wood.
Rough DIFFICULT WOOD (exotic, oak, larch, oiled or greasy...): dilute the 1st coat with 10% water and apply an undiluted2nd coat (avoid too thick an application). On oily wood, degrease first with acetone.
FOR WOOD THAT HAS ALREADY BEEN LASURED: brush to remove loose parts, then sand with 150-grit sandpaper to obtain a smooth surface and remove dust.
APPLICATION
Ideal application conditions: between 12 and 25°C in dry weather.
Stir High Protect Door & Frame Stain vigorously with a long, wide stick before use, paying particular attention to the bottom of the pot, so as to homogenize the product.
Apply one coat in the direction of the wood grain, making sure to cover all hollows and edges. Leave to dry for 3 hours. Apply a2nd coat in the same way and leave to dry for 12 hours.
Remove as much product as possible from tools after use. Do not dispose of residues or wash water/solvents in sinks, toilets, sewers, garbage garbage cans, etc., to avoid release into the environment.
TIPS
For spray application, allow for dilution (max. 10% water) and application in 3 thinner coats.
The colorless variant is for maintenance use only on wood that has already been stained or tinted, or to deconcentrate other shades in the color chart.
Not suitable for use on thermo-heated, heat-treated or acidic wood.
The color, porosity, species and age of the wood can influence the final shade of the substrate. Always test on an inconspicuous area.
Sand with 240-grit sandpaper between 2 coats if the surface feels rough to the touch after the 1st coat.
Avoid wasting woodstain: estimate the amount of woodstain you need.
Close unfinished jars so you can reuse the woodstain.
Reusing woodstain is a good way of reducing the environmental impact of products over their entire life cycle.
Close packaging after use.
When using by spraying, be sure to wear appropriate gloves and clothing, and avoid breathing mists.
8-YEAR WARRANTY
The 8-year warranty covers :
NEW or RESTORED WOODS of common species, in accordance with the preparation
preparation and application.
EXPOSURE: on vertical woodwork only. South and South-West exposure: apply
3 coats.
The guarantee is limited to reimbursement of the product (on presentation of the can and sales receipt) and concerns only the appearance of the stain.
